WHEN YOU NEED A CLIMATE CHAMBER FOR LARGE-VOLUME STABILITY TESTING WITHOUT COMPROMISING MOBILITY. CCKMB-0/10500

A major European university was looking for a large-volume stability testing chamber capable of testing two pallets of packaged pharmaceutical products with a total weight of up to two tons. The pallets could reach a height of 1800 mm, necessitating a large chamber. However, the client also required a mobile system that would allow them to relocate the chamber as needed.

 

The required specifications were:

👉 Testing capacity for two European pallets

👉 Transportable design
👉 Capacity to condition up to 2,000 kg of samples.
 👉 Temperature control from +5°C to +60°C
👉 Relative humidity control with dew points from 2.7°C to +45°C.
👉 Reinforced structure to support over 2,000 kg.

 
OUR SOLUTION: A MODUBLOC climate chamber, CCKMB-0/10500. A modular, mobile chamber thanks to its base structure. The interior dimensions of 2300 x 3000 x 1520 mm (H x W x D) allow for the storage of two full pallets, with a reinforced, high-support floor. A double-leaf door provides full access to the testing area. All of this is controlled by an advanced control system compliant with ICH guidelines.
 

Would you like to more know?
📩 Contact: comercial@dycometal.com
🌐 Web: www.dycometal.com

TEMPERATURE TEST CHAMBER COMBINED WITH TEST BENCH FOR AUTOMOTIVE COMPONENTS. TEMPERATURE TEST CHAMBER, MODEL: CETM-60/2700T-2P

Our client, a leading European engineering firm, wanted to combine their test benches with a thermal testing system (hot/cold) to subject parts to both mechanical and thermal stress, thus verifying their behavior under extreme conditions.

 
The requirements were:
👉 Custom interior design.
👉 Temperature range between -60°C and +180°C.
👉 Various side, ceiling, and floor accesss-ports for integration with the test bench.
👉 Thermal gradients designed to compensate for large masses.
👉 Large viewing windows.
👉 Ability to communicate with their own control system.
 
OUR SOLUTION: Our thermal testing chamber, model CETM-70/2700T-2P. A system with an internal volume of 1500 x 1500 x 1200 mm (H x W x D), with all the technical components located on the right side of the chamber, allowing for seamless integration into the client's test bench. A total of 9 access-ports are distributed along the left side of the test chamber, as well as in the ceiling, floor, and rear. All of this is managed by our 10” touchscreen control system, which can also communicate with the client's existing system.

 

Would you like to more know?

📩 Contact: comercial@dycometal.com

🌐 Web: www.dycometal.com

#dycometal #environmentaltesting #EnvironmentalSimulation #ClimaticTesting #ThermalTesting #temperature #humidity #chamber #testing #climatic #RAndD #Innovation #QualityAssurance #automotive #testbench

CLIMATIC TESTS FOR ENVIRONMENTAL STUDIES OF AUTOMOTIVE LIGHTING. CLIMATE CHAMBER CCK-70/2197T-6

Once again, our client, a renowned manufacturer of automotive lighting systems, contacted us to supply a new climate test chamber. But this time, they needed something more specialized: a cubic design that would allow them to place a model with the lighting installed in vehicle position for climate testing.

The requirements were:
👉 Custom interior design.
👉 Temperature range between -70°C and +150°C.
👉 Relative humidity control.
👉 Cooling and heating gradients of 6 K/min.
👉 Reinforced structure.
👉 Large, highly transparent glass.

OUR SOLUTION: A climate test chamber with a space tailored to the client's needs. A system designed with a cubic interior volume of 1300 x 1300 x 1300 mm (H x W x D). With a temperature range from -70°C to +150°C, heating and cooling rates of 6 K/min, and relative humidity control between 10% and 98%, this unit features two access-ports, mechanical locks with security keys, a reinforced floor, reinforced trays, exterior lighting, and a large, highly transparent glass panel. And of course, our signature blue totem with a large status light houses our advanced control system.

Would you like to more know?

📩 Contact: comercial@dycometal.com

🌐 Web: www.dycometal.com

#dycometal #environmentaltesting #EnvironmentalSimulation #ClimaticTesting #ThermalTesting #temperature #humidity #chamber #testing #climatic #RAndD #Innovation #QualityAssurance #Automotive 

FREEZING TESTS IN THE AERONAUTICAL INDUSTRY. ACR-70/250 HORIZONTAL CHEST FREEZER (AMS 2750)

Our client, a leading company in the aeronautical manufacturing sector, required a horizontal freezer to subject samples to extreme cold. They needed a system that could condition elongated parts and reach ultra-low temperatures, taking into account the total mass to be placed inside.
 
The required specifications were:
👉 Temperature range down to -60°C.
👉 Compliance with AMS 2750 standards.
👉 High stability and uniformity.
👉 Horizontal configuration.
👉 Air-cooled condensation.
 
OUR SOLUTION: An industrial-grade horizontal chest freezer with a usable volume of 250 liters and dimensions of 500 x 1000 x 500 mm (Height x Width x Depth). It features simple control based on an electronic regulator with parameter monitoring and an independent data logger. All of this is compatible with the associated software via the Ethernet TCP/IP communication port.
 
Would you like to more know?
📩 Contact: comercial@dycometal.com
🌐 Web: www.dycometal.com

 
#dycometal #environmentaltesting #EnvironmentalSimulation #ClimaticTesting #ThermalTesting #freezing #Aeronautical #AMS2750 #temperature #freezer #testing #RAndD #Innovation #QualityAssurance

Beyond the Weather: Protecting Technology Against Water (IP Ratings) ⛈️

When an electronic device, street light, or automotive component fails outdoors, the cause is usually the same: a lack of watertightness. Water leaks are the biggest enemy of today's technology.

To ensure your designs are impenetrable, at Dycometal we develop Rain Test Chambers, specifically designed for verifying international protection codes (IP Ratings - IEC 60529):

🔹 Rain Chambers (IP X1 to IP X9K): From vertical dripping water to high-pressure, high-temperature water jets (severe automotive testing), we recreate any storm or industrial wash scenario.

Guaranteeing the watertight seal of your products is synonymous with long-term reliability. At Dycometal, we provide you with the necessary tools to certify it with complete technical rigor.

💧 Is your product ready to withstand the elements? Contact us: www.dycometal.com

#WatertightnessTesting #IPRate #ElectronicEngineering #Automotive #RainTesting #IECStandards #Dycometal

HOW TO TEST LARGE VERTICAL SAMPLES AT POSITIVE TEMPERATURES? AFA-100/1445 OVEN

Our client contacted us because they needed to test large vertical samples and required a forced-air oven to introduce them.
 

The requirements were:
👉 Custom-designed interior with a height of 1700 mm.
👉 Temperature range up to +100 °C
👉 Heating rate of 4 K/min.
👉 Robust structure to support up to 500 kg in less than 1 m².
👉 Ability to perform cooling/heating cycles.

OUR SOLUTION: Our AFA-100/1445 oven, a model designed by and for the client. With interior dimensions of 1700 x 1000 x 850 mm (H x W x D). Robust, with a large door and reinforced hinges to support its weight. The base is sturdy enough to support heavy loads and has leveling casters for easy movement. An air extraction system reduces the temperature inside the stove, and all of this is controlled by a controller with associated software for remote computer operation.

 

Would you like to more know?

📩 Contact: comercial@dycometal.com

🌐 Web: www.dycometal.com

 

#dycometal #environmentaltesting #EnvironmentalSimulation #HeatSimulation #ThermalTesting #temperature #oven #testing #RAndD #Innovation #QualityAssurance

HOW TO TEST ELECTRONIC LOCKS. CCK-45/80T CLIMATIC CHAMBER (CO2)

With the rise of online sales, the demand for lockers has increased significantly, and many of these are installed outdoors. Therefore, they must withstand the most extreme weather conditions, ensuring that the opening/closing mechanism functions correctly under the harshest conditions.
 
Our client, a manufacturer of mechanical and electronic locks, needed equipment to perform environmental testing on their products.

 

The required specifications were:
👉 Compliance with IEC 60068-2 standards for climate testing
👉 Temperature range between -40°C and +150°C
👉 Relative humidity control up to 98% RH
👉 Performance of high temperature and humidity tests.
👉 Small Volume
👉 Eco-friendly CO2-based unit.

 
OUR SOLUTION: One of our small-volume chambers, the CCK-45/80T, with an interior volume of 80 liters (500 x 400 x 400 mm, H x W x D). This chamber allows for the installation of several small locks or one larger lock. Its CO2-based system (R-744) allows for temperatures as low as -45ºC, meeting the customer's needs.

Would you like to more know?
📩 Contact: comercial@dycometal.com
🌐 Web: www.dycometal.com

 

#dycometal #environmentaltesting #EnvironmentalSimulation #ClimaticTesting #ThermalTesting #Lockers #Electronic #temperature #humidity #chamber #testing #CO2 #R744 #IEC60068-2 #climatic #RAndD #Innovation #QualityAssurance