CLIMATIC TESTING FOR BALLISTIC PERFORMANCE OF BALLISTIC VESTS. CCK-20/1000T CLIMATIC CHAMBER

 A client wanted to evaluate the ballistic performance of bulletproof vests over time according to NIJ Standard-0101.06. To do this, they planned to acquire a Tumbler drum unit to combine with a climatic chamber that met the climatic and environmental requirements for the various testing procedures for flexible (soft) and rigid (hard) armor.

The required conditions were:
👉 Adequate interior volume to accommodate the Tumbler drum.
👉 Reinforced floor to support the weight of the Tumbler drum.
👉 Compliance with the environmental conditions specified in NIJ Standard-0101.06.
👉 Extended temperature range for conditioning rigid armor (ballistic plates), Phase 2 cold cycle.
👉 Communication capability with the external drum control system.

OUR SOLUTION: The CCK-20/1000T climate test chamber, adapted in its internal dimensions to the drum's dimensions. The chamber features a front opening of over 180º, allowing access to the test area. Its extended range allows for testing both flexible armor and rigid shielding (phase 1 and phase 2 cold cycle). The system includes an Ethernet port as well as communication signals with the customer's remote control system for the Tumbler drum. All of this is controlled by the advanced control system based on a 7” touchscreen panel.

Would you like to more know? 
📩 Contact: comercial@dycometal.com 
🌐 Web: www.dycometal.com

HOW TO TEST EXTERNAL THERMAL INSULATION SYSTEMS (ETICS)? CCK-25/6800T CLIMATIC CHAMBER

 Our client, a renowned Spanish Certification Center for construction materials, already had several pieces of equipment for performing validation and certification tests on External Thermal Insulation Systems (ETICS). However, due to the workload of the existing equipment, they needed an additional system to increase their validation capacity.

The requirements they were looking for were:
👉 Compliance with European guidelines EAD 040083-00-0404.
👉 Equipment identical to the previously supplied systems.
👉 Ability to test two samples in parallel.
👉 Enclosures for both sides of the chamber for when the chamber is only evaluating one sample or for use as a conventional climatic chamber.

OUR SOLUTION: Our climatic test chamber, model CCK-25/6800T, features a standardized design compliant with European guidelines EAD 040083-00-0404. With an internal volume of 6800 liters, it can test two thermal insulation systems in parallel. The system includes a thermostatically controlled bath to condition the water to the specified temperature and then recirculate it. All of this is controlled by our advanced system, which features a 7” touchscreen panel and associated logging software for PC-based control and recording.

Would you like to more know? 
📩 Contact: comercial@dycometal.com 
🌐 Web: www.dycometal.com

THERMAL SHOCK TESTING OF VEHICLE ACCESS COMPONENTS. CRT2V-40/166T THERMAL SHOCK CHAMBER

 Every vehicle must withstand extreme temperature conditions, from the coldest mornings with sub-zero temperatures to the hottest parts of the day. In this case, our client, a manufacturer of advanced vehicle access, security, and control systems, was looking for a thermal shock chamber for their quality control testing.

The required specifications were:
👉 Medium-sized interior volume.
👉 Thermal shock from -40°C to +200°C.
👉 Compliance with IEC standards.
👉 Compact size.

OUR SOLUTION: Our CRT2V-40/166T thermal shock chamber. In this case, we reduced the camera height using a basket transfer system different from the traditional pneumatic piston system, which allowed us to significantly lower the overall height. The system performed exceptionally well under thermal shock, operating from -40°C to +200°C. All of this was controlled via our advanced 7” touchscreen control system and associated software.

Would you like to more know? 
📩 Contact: comercial@dycometal.com 
🌐 Web: www.dycometal.com

Are you looking for maximum homogeneity and precision in your extreme temperature tests? ❄️

At DYCOMETAL, backed by over 40 years of experience leading the design and manufacture of environmental simulation equipment in Spain, we understand that the reliability of your thermal tests cannot depend on compromises. That's why today we want to highlight one of our most robust and in-demand solutions: our Forced Air Circulation Chests.
What makes our chests stand out in the demanding industrial quality control sector?

• Flexible and precise temperature ranges: We design and manufacture equipment tailored to your specifications with standard ranges of -20ºC, -30ºC, or -70ºC, also offering optimized configurations to consistently reach -45ºC.

• Innovation and sustainability with CO₂: We develop advanced solutions based on CO₂ as an alternative refrigerant, ensuring maximum commitment to the environment and anticipating the strictest European environmental regulations.
• Exceptional homogeneity: Thanks to the forced air circulation system, we guarantee a highly uniform temperature distribution throughout the entire usable volume of the chest, minimizing thermal gradients during testing.
• Custom engineering: Our engineering department studies each project individually to manufacture the exact solution required by the regulations or testing standards of your sector.
• All our equipment is developed entirely at our plant in Viladecans (Barcelona), under the standards of the ISO 9001:2015 certified quality management system and is verified by our own LCIS calibration laboratory.

Do you want to optimize your testing processes with cutting-edge technology and specialized technical support?

Would you like to more know?
📩 Contact: comercial@dycometal.com
🌐 Web: www.dycometal.com

CLIMATIC TESTING FOR DERMATOLOGICAL STUDIES. CLIMATIC CHAMBER CM-10/695T

A leading global pharmaceutical company focused on medical dermatology contacted us to request a climate chamber for stability testing. The project, initially straightforward, had a unique challenge: the installation space was difficult to access.

The requirements were:

👉 Custom design to facilitate equipment access.
👉 Temperature and humidity control.
👉 Demineralized water reserve tank.
 
👉 4 reinforced trays.
👉 Independent communication with their data logging system.

 

OUR SOLUTION: The CCK-10/695T climatic testing chamber. We redesigned this climatic chamber both internally and externally to allow access to the installation area without compromising the chamber's usable volume. The airflow system was redesigned, placing the technical components on the side of the chamber instead of the rear, without sacrificing usable volume. A vertical space was added for storing tall samples. The interior dimensions are 1240 x 585 x 960 mm (H x W x D). It features a security lock to prevent tampering and a 7” touchscreen control system with data transmission to your recording system.

 

Would you like to more know?

📩 Contact: comercial@dycometal.com

🌐 Web: www.dycometal.com

WHEN YOU NEED A CLIMATE CHAMBER FOR LARGE-VOLUME STABILITY TESTING WITHOUT COMPROMISING MOBILITY. CCKMB-0/10500

A major European university was looking for a large-volume stability testing chamber capable of testing two pallets of packaged pharmaceutical products with a total weight of up to two tons. The pallets could reach a height of 1800 mm, necessitating a large chamber. However, the client also required a mobile system that would allow them to relocate the chamber as needed.

 

The required specifications were:

👉 Testing capacity for two European pallets

👉 Transportable design
👉 Capacity to condition up to 2,000 kg of samples.
 👉 Temperature control from +5°C to +60°C
👉 Relative humidity control with dew points from 2.7°C to +45°C.
👉 Reinforced structure to support over 2,000 kg.

 
OUR SOLUTION: A MODUBLOC climate chamber, CCKMB-0/10500. A modular, mobile chamber thanks to its base structure. The interior dimensions of 2300 x 3000 x 1520 mm (H x W x D) allow for the storage of two full pallets, with a reinforced, high-support floor. A double-leaf door provides full access to the testing area. All of this is controlled by an advanced control system compliant with ICH guidelines.
 

Would you like to more know?
📩 Contact: comercial@dycometal.com
🌐 Web: www.dycometal.com

TEMPERATURE TEST CHAMBER COMBINED WITH TEST BENCH FOR AUTOMOTIVE COMPONENTS. TEMPERATURE TEST CHAMBER, MODEL: CETM-60/2700T-2P

Our client, a leading European engineering firm, wanted to combine their test benches with a thermal testing system (hot/cold) to subject parts to both mechanical and thermal stress, thus verifying their behavior under extreme conditions.

 
The requirements were:
👉 Custom interior design.
👉 Temperature range between -60°C and +180°C.
👉 Various side, ceiling, and floor accesss-ports for integration with the test bench.
👉 Thermal gradients designed to compensate for large masses.
👉 Large viewing windows.
👉 Ability to communicate with their own control system.
 
OUR SOLUTION: Our thermal testing chamber, model CETM-70/2700T-2P. A system with an internal volume of 1500 x 1500 x 1200 mm (H x W x D), with all the technical components located on the right side of the chamber, allowing for seamless integration into the client's test bench. A total of 9 access-ports are distributed along the left side of the test chamber, as well as in the ceiling, floor, and rear. All of this is managed by our 10” touchscreen control system, which can also communicate with the client's existing system.

 

Would you like to more know?

📩 Contact: comercial@dycometal.com

🌐 Web: www.dycometal.com

#dycometal #environmentaltesting #EnvironmentalSimulation #ClimaticTesting #ThermalTesting #temperature #humidity #chamber #testing #climatic #RAndD #Innovation #QualityAssurance #automotive #testbench

CLIMATIC TESTS FOR ENVIRONMENTAL STUDIES OF AUTOMOTIVE LIGHTING. CLIMATE CHAMBER CCK-70/2197T-6

Once again, our client, a renowned manufacturer of automotive lighting systems, contacted us to supply a new climate test chamber. But this time, they needed something more specialized: a cubic design that would allow them to place a model with the lighting installed in vehicle position for climate testing.

The requirements were:
👉 Custom interior design.
👉 Temperature range between -70°C and +150°C.
👉 Relative humidity control.
👉 Cooling and heating gradients of 6 K/min.
👉 Reinforced structure.
👉 Large, highly transparent glass.

OUR SOLUTION: A climate test chamber with a space tailored to the client's needs. A system designed with a cubic interior volume of 1300 x 1300 x 1300 mm (H x W x D). With a temperature range from -70°C to +150°C, heating and cooling rates of 6 K/min, and relative humidity control between 10% and 98%, this unit features two access-ports, mechanical locks with security keys, a reinforced floor, reinforced trays, exterior lighting, and a large, highly transparent glass panel. And of course, our signature blue totem with a large status light houses our advanced control system.

Would you like to more know?

📩 Contact: comercial@dycometal.com

🌐 Web: www.dycometal.com

#dycometal #environmentaltesting #EnvironmentalSimulation #ClimaticTesting #ThermalTesting #temperature #humidity #chamber #testing #climatic #RAndD #Innovation #QualityAssurance #Automotive 

HOW ARE VEHICLE LIGHTING FIXTURES TESTED UNDER EXTREME CONDITIONS? CCK-70/1000T-6 CLIMATE CHAMBER

An automotive lighting manufacturer with more than five DYCOMETAL environmental test chambers in its quality control laboratory needed additional equipment similar to what it already had installed.
 
The required conditions were:
👉 Temperature range between -50°C and +180°C.
👉 Standard volume of 1000 liters.
👉 Cooling temperature gradients of 6 K/min.
👉 Heating temperature gradients of 8 K/min.
👉 Reinforced floor and reinforced trays. 

OUR SOLUTION: The climate test chamber previously supplied to this client, the CCK-70/1000T-6, has been updated with a new totem display with an operating status light and a new mechanical locking system with a security key. The client has already tested and verified the system's performance and results. This high-performance heating and cooling unit allows for the most demanding climate tests to be performed on vehicle lighting.
 
Would you like to more know?
📩 Contact: comercial@dycometal.com
🌐 Web: www.dycometal.com

#dycometal #environmentaltesting #lighting #EnvironmentalSimulation #ClimaticTesting #ThermalTesting #Auomotive #temperature #humidity #chamber #testing #climatic #RAndD #Innovation #QualityAssurance

CLIMATIC TESTING FOR ENVIRONMENTAL STUDIES IN THE AUTOMOTIVE INDUSTRY. CLIMATE CHAMBER CCK-48/2000T-2P-10 (CO2)

 Our client, a leading mechatronics company specializing in the automotive sector, was looking for several chambers for its new European production plant. This client sought a system tailored to its design and functionality needs, while maintaining environmentally friendly conditions regarding the construction of the refrigeration unit, which had to be based on CO2 (R-744).

The required specifications were:
👉 Temperature range between -40 ºC and +180 ºC
👉 Custom interior design for testing different types of samples.
👉 Excellent ergonomics for sample insertion.
👉 Heating and cooling speed greater than 4 K/min, considering a heat dissipation of 3 kW and a mass of 50 kg
👉 Environmentally friendly CO2-based unit.
 
OUR SOLUTION: The climatic test chamber with a design specially tailored to the client, our model CCK-48/2000T-2P-10. A chamber with a volume according to the client's needs: 1500 x 1900 x 700 mm (H x W x D), to comfortably accommodate the different samples to be tested. The double door and the shallow depth allow for easy handling of the samples, as well as the placement of the various sensors. These sensors must be registered in the controller itself. Advanced control and control software allow for monitoring all supplied systems.
 
Would you like to more know?
📩 Contact: comercial@dycometal

🌐 Web: www.dycometal.com

#dycometal #environmentaltesting #EnvironmentalSimulation #ClimaticTesting #ThermalTesting #Auomotive #mechatronics #temperature #humidity #chamber #testing #CO2 #R744 #climatic #RAndD #Innovation #QualityAssurance

IEC 60529 TESTING, RAIN TEST, IPX3 AND IPX4 DEGREES. CLL-1000 RAIN TEST CHAMBER

Sometimes our clients don't need a custom solution; a standard solution is sufficient for their environmental testing needs. That's where our standard solutions come in. This was the case for the electronics department of a European university that was looking for a rain test chamber.
 
The requirements were:
👉 Volume of approximately 1000 liters.
👉 Compliance with IEC 60529.
👉 IPX3 and IPX4 protection ratings.
👉 Flow control.
 
OUR SOLUTION: Our standard rain test chamber, model CLL-1000, with a 1000-liter capacity and an 800 mm diameter arch. It features a height-adjustable sample holder and a power supply for the sample. A standard solution for a standard need.
 
Would you like to more know?
📩 Contacto: comercial@dycometal.com
🌐 Web: www.dycometal.com

#dycometal #environmentaltesting #EnvironmentalSimulation #RainTesting #electronic #chamber #IEC60529 #IPX #IPXY #testing #chamber #climatic #RAndD #Innovation #QualityAssurance

HOW DO WE TEMPER HYDROGEN PIPES IN A TENSILE TESTING MACHINE?

THERMAL TEST CHAMBER: CETM-70-156Te.
Our client, a leading manufacturer of piping for the fluid transport sector, wanted to temper hydrogen pipes during tensile testing to evaluate the behavior of the samples under both the forces they endured and at extreme temperatures. For this, they needed a chamber capable of reaching extreme temperatures and perfectly compatible with their existing tensile testing machine.

The required specifications were:
👉 Chamber adapted to their existing tensile testing machine.
👉 Temperature ranges from -70 ºC to +100 ºC.
👉 Mechanical cooling.
👉 Chamber mobility to allow for testing with and without the chamber.
👉 Easy chamber movement.
👉 Side window for recording material behavior during testing.
 
OUR SOLUTION: Our CETM-70/156Te thermal testing chamber is adapted to the customer's existing tensile testing machine and features a chamber extraction system for testing with or without thermal conditioning. It includes a large, highly transparent front and side viewing window. Removable top and bottom ports allow for chamber removal without loosening clamps. All controls are managed via a touchscreen and remote control software, which can be connected to the customer's tensile testing system.
 
Would you like to more know?
📩 Contacto: comercial@dycometal.com
🌐 Web: www.dycometal.com 

#dycometal #environmentaltesting #EnvironmentalSimulation #Tensiletesting #Tesnsilemachine #ThermalTesting #hydrogen #temperature #chamber #testing #RAndD #Innovation #QualityAssurance

HOW TO TEST CERAMIC TILES AGAINST TEMPERATURE CHANGES? AIR-WATER THERMAL SHOCK CHAMBER, CRT2V-300T

 A technology center contacted us because they needed to test ceramic tiles against sudden temperature changes according to the UNE-EN ISO 10545-9 standard, for sample validation, certification, and the development of new materials.

 Their requirements were:
👉 Compliance with EN ISO 10545-9.
👉 Capacity for large samples (650 x 650 mm).
👉 Precise control of all cycle variables.
👉 Remote PC connection.

OUR SOLUTION: Our air-water thermal shock chamber, CRT2VT-300T, a thermal shock chamber with a usable capacity of 300 liters. The system comprises two zones: a positive temperature compartment with a temperature range up to +170°C and a thermostatically controlled bath for sample immersion at +15°C, with a cooling system to chill the water and ensure maximum stability and homogeneity throughout the bath. All of this is controlled by an advanced processor for managing cycles, times, segments, transfer times, and residence times. It also includes associated software for recording all tests and generating test reports.

 Would you like to more know?
📩 Contacto: comercial@dycometal.com
🌐 Web: www.dycometal.com

#dycometal #environmentaltesting #EnvironmentalSimulation #Thermalshock #aritowater #ThermalTesting #buildingmaterial #temperature #humidity #chamber #testing #shock #RAndD #Innovation #QualityAssurance #certification

HOW TO SIMULATE HYGROTHERMAL BEHAVIOR IN COMPLEX BUILDING STRUCTURES AND CONNECTIONS?

CCKMB2-0-30/15000Te CLIMATIC CHAMBER
 
Our client, an Energy and Materials in Infrastructure and Buildings research group at a European University, was looking for an environmental testing system to study and analyze building components under different environmental conditions, simulating indoor/outdoor and winter/summer environments.
 
What did they need?
👉 Two climatic chambers with temperature and humidity control to simulate indoor and outdoor building conditions, with the option of being walkable to introduce sensors, equipment, etc.
👉 A large and robust sample holder to separate chambers with different types of insulation.
👉 Mobility to allow for the placement of large samples between the two chambers. 

👉 Temperature ranges from 0°C to +50°C for indoor conditions.
👉 Temperature ranges from -30°C to +70°C for outdoor conditions.
👉 Relative humidity control in both test chambers.
👉 Synchronized control in both systems, managed by a central system.
 
OUR SOLUTION: The CCKMB2-0-30/15000Te dual-chamber system. An environmental simulation system built with two climatic chambers, one for outdoor conditions and one for indoor conditions, and a mobile sample holder to easily and conveniently position the building component to be tested in the middle, aligning the three systems to prevent leaks at the joints and ensure maximum airtightness. The climatic chambers have a usable volume of 15 m³, allowing easy access for personnel, samples, etc. The control is based on a dual independent system for each chamber, to be able to perform independent temperature and humidity cycles, but all managed from a general PC that can centralize both systems and perform seasonal cycles.
 
Would you like to more know?
📩 Contacto: comercial@dycometal.com
🌐 Web: www.dycometal.com

#dycometal #environmentaltesting #EnvironmentalSimulation #ClimaticTesting #ThermalTesting #buildingmaterial #temperature #humidity #chamber #testing #chamber #climatic #RAndD #Innovation #QualityAssurance

🌡️ DOES YOUR PRODUCT WITHSTAND REAL-WORLD STRESS? THE THERMAL SHOCK CHALLENGE.

In a global market where reliability is the minimum standard, thermal stress testing is no longer optional. At DYCOMETAL, we have spent over 40 years designing solutions to push materials to their limits, ensuring safety before they ever reach the market.  

Our range of Thermal Shock Chambers (CRT2V) enables extreme temperature transitions in seconds, simulating aggressive conditions in a controlled and precise manner. 

What sets us apart?
·        In-house Engineering: We design and manufacture every component at our plant in Viladecans. 
·        Testing Versatility: Vertical and horizontal models, including air-to-water systems, to comply with the most demanding international standards. 
·        Commitment to Quality: All our equipment is verified in our own LCIS calibration laboratory, under ISO 9001:2015 standards. 

We don't just manufacture chambers; we are your strategic partner in quality control.

 Would you like to more know? 
📩 Contacto: comercial@dycometal.com
🌐 Web: www.dycometal.com

  #Dycometal #EnvironmentalSimulation #QualityControl #ReliabilityEngineering #ThermalShock #TestingTechnology #AutomotiveEngineering #AerospaceTesting #MaterialsScience #ISO9001

CLIMATIC TEST CHAMBER FOR PACKAGING VALIDATION. CLIMATE CHAMBER CCKMB-40-5625T

Our client, a renowned independent laboratory specializing in the physical testing and validation of packaging for transport, needed to increase the number of units to expand its climate testing capacity.

The required specifications were:

👉 Medium-to-large chamber volume for all types of samples.

👉 Modular chamber that could be easily moved if needed.

👉 Temperature range down to -40ºC for ultra-freezing tests.

👉 Humidity control.

👉 High stability and uniformity.

OUR SOLUTION: Based on other models supplied to this client, we opted for two MODUBLOC climatic chambers, models CCK-40/5625T. These chambers have a 5.6 m³ internal volume capacity, a large access door, and a very vertical design to accommodate tall samples. The interior is made of stainless steel, and the exterior is mounted on a frame that allows for easy movement of the entire chamber unit if needed, while also providing a natural cooling zone. Temperature ranges from -40°C to +80°C, with gradients tailored to the client's requirements. All of this is controlled by an advanced touchscreen controller.

Would you like to more know? / ¿Te gustaría saber más?

📩 Contacto: comercial@dycometal.com

🌐 Web: www.dycometal.com

DID YOU KNOW THAT DYCOMETAL HAS BEEN MANUFACTURING BATTERY CHAMBERS FOR OVER 20 YEARS?

At DYCOMETAL, we have been designing and manufacturing specialized battery testing chambers for over two decades, back when many manufacturers were still not considering the real safety requirements of these types of applications.

Our experience has allowed us to develop systems with added safety features and solutions adapted to the risks associated with battery testing, especially in demanding sectors such as automotive, electric mobility, electronics, and energy storage.

OUR SOLUTION (2016): A CETM-70/1000, a 1000-liter thermal testing chamber. This reinforced unit is designed to test masses exceeding 250 kg, with a temperature gradient of 1°C/min between +120°C and -20°C, taking into account the mass and heat dissipation within the system. The system was built taking into account EUCAR risks, incorporating high safety standards such as an overpressure evacuation system, electromagnetic lock, gas meters, etc. All of this is designed to guarantee maximum safety and reliability.

Because when it comes to battery testing, experience and safety are not optional.

Would you like to more know?

📩 Contacto: comercial@dycometal.com

🌐 Web: www.dycometal.com

INTELLIGENT THERMAL CONTROL FOR HIGH-DENSITY RACKS. CLIMATIC CHAMBER CCK-0-6264m

In an increasingly digital world, the reliability of IT infrastructure is a critical factor to consider. As computing power increases, so does the energy dissipated by servers… and, with it, the heat generated in the racks. This thermal increase not only impacts performance but can also compromise the stability and lifespan of the infrastructure if not properly managed.
 
What is needed?:
👉 Modular chambers with wide door openings.
👉 Multiple access points.
👉 High capacity for compensating dissipated energy.
👉 Optimized airflow.
👉 Humidity control.
 
OUR SOLUTION: DYCOMETAL has been manufacturing controlled environment chambers for server conditioning since 2017, such as our CCK-0/6264m chamber, a modular chamber with high dissipation capacity and optimized airflow to remove generated heat and maintain the appropriate internal operating conditions for server racks. The chamber has a large door for accessing larger racks, as well as two auxiliary doors for convenient access to the servers from any side of the chamber. It features a reinforced and insulated floor, minimizing heat loss.
The client also requested relative humidity control to ensure controlled conditions across all possible variables.
All of this is controlled by an advanced microprocessor connected to its central control unit and an independent temperature recording system at various points in the rack, guaranteeing maximum stability and uniformity both temporally and spatially.

Would you like to more know? 

📩 Contacto: comercial@dycometal.com
🌐 Web: www.dycometal.com

CLIMATIC TESTING FOR CONSTRUCTION MATERIALS. CCK-30/1500T CLIMATIC CHAMBER

A major European university needed a chamber to conduct climatic tests on thermal and acoustic insulation materials, controlling temperature and humidity. This client already owned freeze-thaw (FTH) chambers from our company and entrusted us with the task of finding a suitable chamber for their needs.

The required specifications were:
👉 Medium-to-large chamber volume for all types of samples.
👉 Temperature range suitable for construction materials.
👉 Humidity control.
👉 High stability and uniformity.
 
OUR SOLUTION: The 1500-liter climatic test chamber, MODEL: CCK-30/1500T. This 1500-liter chamber, measuring 1000 x 1000 x 1500 mm (H x W x D), provided ample space for long test specimens. The chamber offered a temperature range from -30°C to +150°C and cooling gradients of 2.5 K/min and heating gradients of 4 K/min, enabling it to perform even some freeze-thaw tests. The CCK-T systems feature extended relative humidity control for conducting tests with more demanding humidity requirements. All of this was controlled via an advanced 7” touchscreen control system and our new totem with an operating status indicator light.

Would you like to more know?
📩 Contacto: comercial@dycometal.com
🌐 Web: www.dycometal.com

CLIMATIC TESTING ON SELF-ADHESIVE LABELS. 🏷🏷

MODEL CCK-20/48T
Climatic testing of self-adhesive labels is essential to ensure that the product does not peel, fade, or degrade prematurely. When writing a report or test plan, you should focus on how the face (fronting material), the adhesive, and the substrate (application surface) interact under environmental stress.
 
👉 Temperature Resistance
👉 Humidity and Condensation Resistance
👉 Post-Climate Mechanical Testing
 
Initial requirements for selecting the most suitable chamber could be:
• Small volume.
• Negative temperature ranges.
• Relative humidity control.
• Data logging system for reporting.
 
OUR SOLUTION: Our smallest climatic chamber, the DYCOMETAL CCK-20/48T, with a capacity of 48 liters. A compact benchtop chamber, both internally and externally, for easy installation in the laboratory, enabling the testing of small samples. With a temperature range from -20°C to +150°C and extended relative humidity control, it allows samples to be subjected to the ambient conditions of storage and transport. Advanced controls and software enable the recording of all test data for subsequent report generation.

📩 Contacto: comercial@dycometal.com

🌐 Web: www.dycometal.com