CLIMATIC TESTING FOR BALLISTIC PERFORMANCE OF BALLISTIC VESTS. CCK-20/1000T CLIMATIC CHAMBER

 A client wanted to evaluate the ballistic performance of bulletproof vests over time according to NIJ Standard-0101.06. To do this, they planned to acquire a Tumbler drum unit to combine with a climatic chamber that met the climatic and environmental requirements for the various testing procedures for flexible (soft) and rigid (hard) armor.

The required conditions were:
👉 Adequate interior volume to accommodate the Tumbler drum.
👉 Reinforced floor to support the weight of the Tumbler drum.
👉 Compliance with the environmental conditions specified in NIJ Standard-0101.06.
👉 Extended temperature range for conditioning rigid armor (ballistic plates), Phase 2 cold cycle.
👉 Communication capability with the external drum control system.

OUR SOLUTION: The CCK-20/1000T climate test chamber, adapted in its internal dimensions to the drum's dimensions. The chamber features a front opening of over 180º, allowing access to the test area. Its extended range allows for testing both flexible armor and rigid shielding (phase 1 and phase 2 cold cycle). The system includes an Ethernet port as well as communication signals with the customer's remote control system for the Tumbler drum. All of this is controlled by the advanced control system based on a 7” touchscreen panel.

Would you like to more know? 
📩 Contact: comercial@dycometal.com 
🌐 Web: www.dycometal.com

HOW TO TEST EXTERNAL THERMAL INSULATION SYSTEMS (ETICS)? CCK-25/6800T CLIMATIC CHAMBER

 Our client, a renowned Spanish Certification Center for construction materials, already had several pieces of equipment for performing validation and certification tests on External Thermal Insulation Systems (ETICS). However, due to the workload of the existing equipment, they needed an additional system to increase their validation capacity.

The requirements they were looking for were:
👉 Compliance with European guidelines EAD 040083-00-0404.
👉 Equipment identical to the previously supplied systems.
👉 Ability to test two samples in parallel.
👉 Enclosures for both sides of the chamber for when the chamber is only evaluating one sample or for use as a conventional climatic chamber.

OUR SOLUTION: Our climatic test chamber, model CCK-25/6800T, features a standardized design compliant with European guidelines EAD 040083-00-0404. With an internal volume of 6800 liters, it can test two thermal insulation systems in parallel. The system includes a thermostatically controlled bath to condition the water to the specified temperature and then recirculate it. All of this is controlled by our advanced system, which features a 7” touchscreen panel and associated logging software for PC-based control and recording.

Would you like to more know? 
📩 Contact: comercial@dycometal.com 
🌐 Web: www.dycometal.com

THERMAL SHOCK TESTING OF VEHICLE ACCESS COMPONENTS. CRT2V-40/166T THERMAL SHOCK CHAMBER

 Every vehicle must withstand extreme temperature conditions, from the coldest mornings with sub-zero temperatures to the hottest parts of the day. In this case, our client, a manufacturer of advanced vehicle access, security, and control systems, was looking for a thermal shock chamber for their quality control testing.

The required specifications were:
👉 Medium-sized interior volume.
👉 Thermal shock from -40°C to +200°C.
👉 Compliance with IEC standards.
👉 Compact size.

OUR SOLUTION: Our CRT2V-40/166T thermal shock chamber. In this case, we reduced the camera height using a basket transfer system different from the traditional pneumatic piston system, which allowed us to significantly lower the overall height. The system performed exceptionally well under thermal shock, operating from -40°C to +200°C. All of this was controlled via our advanced 7” touchscreen control system and associated software.

Would you like to more know? 
📩 Contact: comercial@dycometal.com 
🌐 Web: www.dycometal.com

Are you looking for maximum homogeneity and precision in your extreme temperature tests? ❄️

At DYCOMETAL, backed by over 40 years of experience leading the design and manufacture of environmental simulation equipment in Spain, we understand that the reliability of your thermal tests cannot depend on compromises. That's why today we want to highlight one of our most robust and in-demand solutions: our Forced Air Circulation Chests.
What makes our chests stand out in the demanding industrial quality control sector?

• Flexible and precise temperature ranges: We design and manufacture equipment tailored to your specifications with standard ranges of -20ºC, -30ºC, or -70ºC, also offering optimized configurations to consistently reach -45ºC.

• Innovation and sustainability with CO₂: We develop advanced solutions based on CO₂ as an alternative refrigerant, ensuring maximum commitment to the environment and anticipating the strictest European environmental regulations.
• Exceptional homogeneity: Thanks to the forced air circulation system, we guarantee a highly uniform temperature distribution throughout the entire usable volume of the chest, minimizing thermal gradients during testing.
• Custom engineering: Our engineering department studies each project individually to manufacture the exact solution required by the regulations or testing standards of your sector.
• All our equipment is developed entirely at our plant in Viladecans (Barcelona), under the standards of the ISO 9001:2015 certified quality management system and is verified by our own LCIS calibration laboratory.

Do you want to optimize your testing processes with cutting-edge technology and specialized technical support?

Would you like to more know?
📩 Contact: comercial@dycometal.com
🌐 Web: www.dycometal.com

CLIMATIC TESTING FOR DERMATOLOGICAL STUDIES. CLIMATIC CHAMBER CM-10/695T

A leading global pharmaceutical company focused on medical dermatology contacted us to request a climate chamber for stability testing. The project, initially straightforward, had a unique challenge: the installation space was difficult to access.

The requirements were:

👉 Custom design to facilitate equipment access.
👉 Temperature and humidity control.
👉 Demineralized water reserve tank.
 
👉 4 reinforced trays.
👉 Independent communication with their data logging system.

 

OUR SOLUTION: The CCK-10/695T climatic testing chamber. We redesigned this climatic chamber both internally and externally to allow access to the installation area without compromising the chamber's usable volume. The airflow system was redesigned, placing the technical components on the side of the chamber instead of the rear, without sacrificing usable volume. A vertical space was added for storing tall samples. The interior dimensions are 1240 x 585 x 960 mm (H x W x D). It features a security lock to prevent tampering and a 7” touchscreen control system with data transmission to your recording system.

 

Would you like to more know?

📩 Contact: comercial@dycometal.com

🌐 Web: www.dycometal.com

WHEN YOU NEED A CLIMATE CHAMBER FOR LARGE-VOLUME STABILITY TESTING WITHOUT COMPROMISING MOBILITY. CCKMB-0/10500

A major European university was looking for a large-volume stability testing chamber capable of testing two pallets of packaged pharmaceutical products with a total weight of up to two tons. The pallets could reach a height of 1800 mm, necessitating a large chamber. However, the client also required a mobile system that would allow them to relocate the chamber as needed.

 

The required specifications were:

👉 Testing capacity for two European pallets

👉 Transportable design
👉 Capacity to condition up to 2,000 kg of samples.
 👉 Temperature control from +5°C to +60°C
👉 Relative humidity control with dew points from 2.7°C to +45°C.
👉 Reinforced structure to support over 2,000 kg.

 
OUR SOLUTION: A MODUBLOC climate chamber, CCKMB-0/10500. A modular, mobile chamber thanks to its base structure. The interior dimensions of 2300 x 3000 x 1520 mm (H x W x D) allow for the storage of two full pallets, with a reinforced, high-support floor. A double-leaf door provides full access to the testing area. All of this is controlled by an advanced control system compliant with ICH guidelines.
 

Would you like to more know?
📩 Contact: comercial@dycometal.com
🌐 Web: www.dycometal.com

TEMPERATURE TEST CHAMBER COMBINED WITH TEST BENCH FOR AUTOMOTIVE COMPONENTS. TEMPERATURE TEST CHAMBER, MODEL: CETM-60/2700T-2P

Our client, a leading European engineering firm, wanted to combine their test benches with a thermal testing system (hot/cold) to subject parts to both mechanical and thermal stress, thus verifying their behavior under extreme conditions.

 
The requirements were:
👉 Custom interior design.
👉 Temperature range between -60°C and +180°C.
👉 Various side, ceiling, and floor accesss-ports for integration with the test bench.
👉 Thermal gradients designed to compensate for large masses.
👉 Large viewing windows.
👉 Ability to communicate with their own control system.
 
OUR SOLUTION: Our thermal testing chamber, model CETM-70/2700T-2P. A system with an internal volume of 1500 x 1500 x 1200 mm (H x W x D), with all the technical components located on the right side of the chamber, allowing for seamless integration into the client's test bench. A total of 9 access-ports are distributed along the left side of the test chamber, as well as in the ceiling, floor, and rear. All of this is managed by our 10” touchscreen control system, which can also communicate with the client's existing system.

 

Would you like to more know?

📩 Contact: comercial@dycometal.com

🌐 Web: www.dycometal.com

#dycometal #environmentaltesting #EnvironmentalSimulation #ClimaticTesting #ThermalTesting #temperature #humidity #chamber #testing #climatic #RAndD #Innovation #QualityAssurance #automotive #testbench

CLIMATIC TESTS FOR ENVIRONMENTAL STUDIES OF AUTOMOTIVE LIGHTING. CLIMATE CHAMBER CCK-70/2197T-6

Once again, our client, a renowned manufacturer of automotive lighting systems, contacted us to supply a new climate test chamber. But this time, they needed something more specialized: a cubic design that would allow them to place a model with the lighting installed in vehicle position for climate testing.

The requirements were:
👉 Custom interior design.
👉 Temperature range between -70°C and +150°C.
👉 Relative humidity control.
👉 Cooling and heating gradients of 6 K/min.
👉 Reinforced structure.
👉 Large, highly transparent glass.

OUR SOLUTION: A climate test chamber with a space tailored to the client's needs. A system designed with a cubic interior volume of 1300 x 1300 x 1300 mm (H x W x D). With a temperature range from -70°C to +150°C, heating and cooling rates of 6 K/min, and relative humidity control between 10% and 98%, this unit features two access-ports, mechanical locks with security keys, a reinforced floor, reinforced trays, exterior lighting, and a large, highly transparent glass panel. And of course, our signature blue totem with a large status light houses our advanced control system.

Would you like to more know?

📩 Contact: comercial@dycometal.com

🌐 Web: www.dycometal.com

#dycometal #environmentaltesting #EnvironmentalSimulation #ClimaticTesting #ThermalTesting #temperature #humidity #chamber #testing #climatic #RAndD #Innovation #QualityAssurance #Automotive 

FREEZING TESTS IN THE AERONAUTICAL INDUSTRY. ACR-70/250 HORIZONTAL CHEST FREEZER (AMS 2750)

Our client, a leading company in the aeronautical manufacturing sector, required a horizontal freezer to subject samples to extreme cold. They needed a system that could condition elongated parts and reach ultra-low temperatures, taking into account the total mass to be placed inside.
 
The required specifications were:
👉 Temperature range down to -60°C.
👉 Compliance with AMS 2750 standards.
👉 High stability and uniformity.
👉 Horizontal configuration.
👉 Air-cooled condensation.
 
OUR SOLUTION: An industrial-grade horizontal chest freezer with a usable volume of 250 liters and dimensions of 500 x 1000 x 500 mm (Height x Width x Depth). It features simple control based on an electronic regulator with parameter monitoring and an independent data logger. All of this is compatible with the associated software via the Ethernet TCP/IP communication port.
 
Would you like to more know?
📩 Contact: comercial@dycometal.com
🌐 Web: www.dycometal.com

 
#dycometal #environmentaltesting #EnvironmentalSimulation #ClimaticTesting #ThermalTesting #freezing #Aeronautical #AMS2750 #temperature #freezer #testing #RAndD #Innovation #QualityAssurance

Beyond the Weather: Protecting Technology Against Water (IP Ratings) ⛈️

When an electronic device, street light, or automotive component fails outdoors, the cause is usually the same: a lack of watertightness. Water leaks are the biggest enemy of today's technology.

To ensure your designs are impenetrable, at Dycometal we develop Rain Test Chambers, specifically designed for verifying international protection codes (IP Ratings - IEC 60529):

🔹 Rain Chambers (IP X1 to IP X9K): From vertical dripping water to high-pressure, high-temperature water jets (severe automotive testing), we recreate any storm or industrial wash scenario.

Guaranteeing the watertight seal of your products is synonymous with long-term reliability. At Dycometal, we provide you with the necessary tools to certify it with complete technical rigor.

💧 Is your product ready to withstand the elements? Contact us: www.dycometal.com

#WatertightnessTesting #IPRate #ElectronicEngineering #Automotive #RainTesting #IECStandards #Dycometal

HOW TO TEST LARGE VERTICAL SAMPLES AT POSITIVE TEMPERATURES? AFA-100/1445 OVEN

Our client contacted us because they needed to test large vertical samples and required a forced-air oven to introduce them.
 

The requirements were:
👉 Custom-designed interior with a height of 1700 mm.
👉 Temperature range up to +100 °C
👉 Heating rate of 4 K/min.
👉 Robust structure to support up to 500 kg in less than 1 m².
👉 Ability to perform cooling/heating cycles.

OUR SOLUTION: Our AFA-100/1445 oven, a model designed by and for the client. With interior dimensions of 1700 x 1000 x 850 mm (H x W x D). Robust, with a large door and reinforced hinges to support its weight. The base is sturdy enough to support heavy loads and has leveling casters for easy movement. An air extraction system reduces the temperature inside the stove, and all of this is controlled by a controller with associated software for remote computer operation.

 

Would you like to more know?

📩 Contact: comercial@dycometal.com

🌐 Web: www.dycometal.com

 

#dycometal #environmentaltesting #EnvironmentalSimulation #HeatSimulation #ThermalTesting #temperature #oven #testing #RAndD #Innovation #QualityAssurance

HOW TO TEST ELECTRONIC LOCKS. CCK-45/80T CLIMATIC CHAMBER (CO2)

With the rise of online sales, the demand for lockers has increased significantly, and many of these are installed outdoors. Therefore, they must withstand the most extreme weather conditions, ensuring that the opening/closing mechanism functions correctly under the harshest conditions.
 
Our client, a manufacturer of mechanical and electronic locks, needed equipment to perform environmental testing on their products.

 

The required specifications were:
👉 Compliance with IEC 60068-2 standards for climate testing
👉 Temperature range between -40°C and +150°C
👉 Relative humidity control up to 98% RH
👉 Performance of high temperature and humidity tests.
👉 Small Volume
👉 Eco-friendly CO2-based unit.

 
OUR SOLUTION: One of our small-volume chambers, the CCK-45/80T, with an interior volume of 80 liters (500 x 400 x 400 mm, H x W x D). This chamber allows for the installation of several small locks or one larger lock. Its CO2-based system (R-744) allows for temperatures as low as -45ºC, meeting the customer's needs.

Would you like to more know?
📩 Contact: comercial@dycometal.com
🌐 Web: www.dycometal.com

 

#dycometal #environmentaltesting #EnvironmentalSimulation #ClimaticTesting #ThermalTesting #Lockers #Electronic #temperature #humidity #chamber #testing #CO2 #R744 #IEC60068-2 #climatic #RAndD #Innovation #QualityAssurance

Dycometal CH-300 Chamber for Water Condensation Testing (ISO 6270-2) 🔬💧

 Continuous humidity is one of the most aggressive factors for coatings and surface finishes. Predicting how water condensation will affect paint adhesion or blistering is vital before launching any component to market.

Our CH-300 chamber is specifically designed and manufactured to perform humidity resistance tests under the stringent ISO 6270-2 standard:
👉 Constant condensation atmospheres: Continuous maintenance of 100% humidity by heating the water at the bottom of the chamber.
👉 Durable construction: Manufactured with materials of high thermal and chemical resistance to guarantee maximum equipment durability and test repeatability.

The CH-300 provides the controlled and standardized environment that paint and surface treatment laboratories need to certify the highest quality.

🔗 Discover the technical specifications of our corrosion range at: www.dycometal.com

#Corrosion #HumidityTests #ISO6270 #PaintsAndCoatings #QualityControl #CH300 #Dycometal

HOW ARE VEHICLE LIGHTING FIXTURES TESTED UNDER EXTREME CONDITIONS? CCK-70/1000T-6 CLIMATE CHAMBER

An automotive lighting manufacturer with more than five DYCOMETAL environmental test chambers in its quality control laboratory needed additional equipment similar to what it already had installed.
 
The required conditions were:
👉 Temperature range between -50°C and +180°C.
👉 Standard volume of 1000 liters.
👉 Cooling temperature gradients of 6 K/min.
👉 Heating temperature gradients of 8 K/min.
👉 Reinforced floor and reinforced trays. 

OUR SOLUTION: The climate test chamber previously supplied to this client, the CCK-70/1000T-6, has been updated with a new totem display with an operating status light and a new mechanical locking system with a security key. The client has already tested and verified the system's performance and results. This high-performance heating and cooling unit allows for the most demanding climate tests to be performed on vehicle lighting.
 
Would you like to more know?
📩 Contact: comercial@dycometal.com
🌐 Web: www.dycometal.com

#dycometal #environmentaltesting #lighting #EnvironmentalSimulation #ClimaticTesting #ThermalTesting #Auomotive #temperature #humidity #chamber #testing #climatic #RAndD #Innovation #QualityAssurance

CLIMATIC TESTING FOR ENVIRONMENTAL STUDIES IN THE AUTOMOTIVE INDUSTRY. CLIMATE CHAMBER CCK-48/2000T-2P-10 (CO2)

 Our client, a leading mechatronics company specializing in the automotive sector, was looking for several chambers for its new European production plant. This client sought a system tailored to its design and functionality needs, while maintaining environmentally friendly conditions regarding the construction of the refrigeration unit, which had to be based on CO2 (R-744).

The required specifications were:
👉 Temperature range between -40 ºC and +180 ºC
👉 Custom interior design for testing different types of samples.
👉 Excellent ergonomics for sample insertion.
👉 Heating and cooling speed greater than 4 K/min, considering a heat dissipation of 3 kW and a mass of 50 kg
👉 Environmentally friendly CO2-based unit.
 
OUR SOLUTION: The climatic test chamber with a design specially tailored to the client, our model CCK-48/2000T-2P-10. A chamber with a volume according to the client's needs: 1500 x 1900 x 700 mm (H x W x D), to comfortably accommodate the different samples to be tested. The double door and the shallow depth allow for easy handling of the samples, as well as the placement of the various sensors. These sensors must be registered in the controller itself. Advanced control and control software allow for monitoring all supplied systems.
 
Would you like to more know?
📩 Contact: comercial@dycometal

🌐 Web: www.dycometal.com

#dycometal #environmentaltesting #EnvironmentalSimulation #ClimaticTesting #ThermalTesting #Auomotive #mechatronics #temperature #humidity #chamber #testing #CO2 #R744 #climatic #RAndD #Innovation #QualityAssurance

IEC 60529 TESTING, RAIN TEST, IPX3 AND IPX4 DEGREES. CLL-1000 RAIN TEST CHAMBER

Sometimes our clients don't need a custom solution; a standard solution is sufficient for their environmental testing needs. That's where our standard solutions come in. This was the case for the electronics department of a European university that was looking for a rain test chamber.
 
The requirements were:
👉 Volume of approximately 1000 liters.
👉 Compliance with IEC 60529.
👉 IPX3 and IPX4 protection ratings.
👉 Flow control.
 
OUR SOLUTION: Our standard rain test chamber, model CLL-1000, with a 1000-liter capacity and an 800 mm diameter arch. It features a height-adjustable sample holder and a power supply for the sample. A standard solution for a standard need.
 
Would you like to more know?
📩 Contacto: comercial@dycometal.com
🌐 Web: www.dycometal.com

#dycometal #environmentaltesting #EnvironmentalSimulation #RainTesting #electronic #chamber #IEC60529 #IPX #IPXY #testing #chamber #climatic #RAndD #Innovation #QualityAssurance

DETECTION OF PREMATURE FAILURES IN ELECTRONIC COMPONENTS, BURN-IN TEST. AFA-100/768

Our client, a major manufacturer of electronics for telecommunications satellites, already had 7 AFA-100/768 ovens, but due to increased production, they needed to expand the number of environmental tests under controlled temperature conditions, ensuring proper functioning during component development.
 
The conditions they were looking for were similar to the previous ones:
👉 High stability and reproducibility.
👉 Oven with a large vertical load capacity.
👉 4 large-diameter through-wall ports for probe insertion.
👉 Programmable start/stop of the test.
👉 Communication with a central PC for control and recording of all ovens via software.
 
OUR SOLUTION: The same system we previously supplied. Three (3) AFA-100/768 ovens with internal dimensions of 1200 x 800 x 800 mm (H x W x D), featuring high temperature stability. This robust system boasts a high vertical load capacity and, thanks to its associated software and communication port, allows for centralized control of all ovens on one or more PCs simultaneously, enabling parallel monitoring and recording of all systems.
 
Would you like to more know?
📩 Contacto: comercial@dycometal.com
🌐 Web: www.dycometal.com

#dycometal #environmentaltesting #EnvironmentalSimulation #heat #ThermalTesting #electronic #temperature #satellite #oven #testing #chamber #RAndD #Innovation #QualityAssurance

HOW DO WE TEMPER HYDROGEN PIPES IN A TENSILE TESTING MACHINE?

THERMAL TEST CHAMBER: CETM-70-156Te.
Our client, a leading manufacturer of piping for the fluid transport sector, wanted to temper hydrogen pipes during tensile testing to evaluate the behavior of the samples under both the forces they endured and at extreme temperatures. For this, they needed a chamber capable of reaching extreme temperatures and perfectly compatible with their existing tensile testing machine.

The required specifications were:
👉 Chamber adapted to their existing tensile testing machine.
👉 Temperature ranges from -70 ºC to +100 ºC.
👉 Mechanical cooling.
👉 Chamber mobility to allow for testing with and without the chamber.
👉 Easy chamber movement.
👉 Side window for recording material behavior during testing.
 
OUR SOLUTION: Our CETM-70/156Te thermal testing chamber is adapted to the customer's existing tensile testing machine and features a chamber extraction system for testing with or without thermal conditioning. It includes a large, highly transparent front and side viewing window. Removable top and bottom ports allow for chamber removal without loosening clamps. All controls are managed via a touchscreen and remote control software, which can be connected to the customer's tensile testing system.
 
Would you like to more know?
📩 Contacto: comercial@dycometal.com
🌐 Web: www.dycometal.com 

#dycometal #environmentaltesting #EnvironmentalSimulation #Tensiletesting #Tesnsilemachine #ThermalTesting #hydrogen #temperature #chamber #testing #RAndD #Innovation #QualityAssurance

How can you guarantee the performance of your products under the most demanding environmental conditions?

In the development of industrial, automotive, or electronic components, uncertainty is not an option. Ambient temperature and humidity simulations must be accurate, reproducible, and aligned with the highest international standards.
 
With the Dycometal T Series, we raise the bar in climatic and thermal testing:
👉 Precision control: Thermal stability and homogeneous distribution to guarantee reliable results.
👉 Real sustainability: Equipment designed according to European F-Gas regulations, using refrigerants with low environmental impact (GWP < 150).
👉 Technical robustness: High-density insulation and components designed to withstand continuous and severe operating conditions.
 
High-precision environmental simulation is the ultimate bridge between design and market success.
 
🔬 Want to know the real-world performance of your components? Discover the full range of simulation tools on our website: www.dycometal.com

#dycometal #environmentaltesting  #ClimaticTesting #ThermalTesting #buildingmaterial #temperature #humidity #chamber #testing #chamber #climatic #RAndD #Innovation #QualityAssurance

HOW TO TEST CERAMIC TILES AGAINST TEMPERATURE CHANGES? AIR-WATER THERMAL SHOCK CHAMBER, CRT2V-300T

 A technology center contacted us because they needed to test ceramic tiles against sudden temperature changes according to the UNE-EN ISO 10545-9 standard, for sample validation, certification, and the development of new materials.

 Their requirements were:
👉 Compliance with EN ISO 10545-9.
👉 Capacity for large samples (650 x 650 mm).
👉 Precise control of all cycle variables.
👉 Remote PC connection.

OUR SOLUTION: Our air-water thermal shock chamber, CRT2VT-300T, a thermal shock chamber with a usable capacity of 300 liters. The system comprises two zones: a positive temperature compartment with a temperature range up to +170°C and a thermostatically controlled bath for sample immersion at +15°C, with a cooling system to chill the water and ensure maximum stability and homogeneity throughout the bath. All of this is controlled by an advanced processor for managing cycles, times, segments, transfer times, and residence times. It also includes associated software for recording all tests and generating test reports.

 Would you like to more know?
📩 Contacto: comercial@dycometal.com
🌐 Web: www.dycometal.com

#dycometal #environmentaltesting #EnvironmentalSimulation #Thermalshock #aritowater #ThermalTesting #buildingmaterial #temperature #humidity #chamber #testing #shock #RAndD #Innovation #QualityAssurance #certification

HOW TO SIMULATE HYGROTHERMAL BEHAVIOR IN COMPLEX BUILDING STRUCTURES AND CONNECTIONS?

CCKMB2-0-30/15000Te CLIMATIC CHAMBER
 
Our client, an Energy and Materials in Infrastructure and Buildings research group at a European University, was looking for an environmental testing system to study and analyze building components under different environmental conditions, simulating indoor/outdoor and winter/summer environments.
 
What did they need?
👉 Two climatic chambers with temperature and humidity control to simulate indoor and outdoor building conditions, with the option of being walkable to introduce sensors, equipment, etc.
👉 A large and robust sample holder to separate chambers with different types of insulation.
👉 Mobility to allow for the placement of large samples between the two chambers. 

👉 Temperature ranges from 0°C to +50°C for indoor conditions.
👉 Temperature ranges from -30°C to +70°C for outdoor conditions.
👉 Relative humidity control in both test chambers.
👉 Synchronized control in both systems, managed by a central system.
 
OUR SOLUTION: The CCKMB2-0-30/15000Te dual-chamber system. An environmental simulation system built with two climatic chambers, one for outdoor conditions and one for indoor conditions, and a mobile sample holder to easily and conveniently position the building component to be tested in the middle, aligning the three systems to prevent leaks at the joints and ensure maximum airtightness. The climatic chambers have a usable volume of 15 m³, allowing easy access for personnel, samples, etc. The control is based on a dual independent system for each chamber, to be able to perform independent temperature and humidity cycles, but all managed from a general PC that can centralize both systems and perform seasonal cycles.
 
Would you like to more know?
📩 Contacto: comercial@dycometal.com
🌐 Web: www.dycometal.com

#dycometal #environmentaltesting #EnvironmentalSimulation #ClimaticTesting #ThermalTesting #buildingmaterial #temperature #humidity #chamber #testing #chamber #climatic #RAndD #Innovation #QualityAssurance