HOLIDAYS

UNE-EN-60068-2-11, NEUTRAL SALT SPRAY TEST (NSS)

The purpose of this test is to determine the capacity of the equipment to be stored or used under conditions of high humidity combined with high salinity conditions. This test is known like NSS test (Neutral Salt Spray test).

The sample will be tested in a neutral salinity atmosphere (pH 6,5 -7,2), with a fallout rate between 1 and 2 ml/80cm2/hour, while the temperature of the chamber  is +35ºC, the time of the test could vary.

More information: www.dycometal.com 

SSC-400, SALT SPRAY CHAMBER (400 Liters)

DYCOMETAL, company with over 25 years experience in developing simulation chambers for environmental testing, offers customers Salt Spray Chambers to carry out climatic tests.

UNE-EN-60068-2-30, DAMP HEAT TEST, Cyclic

The purpose of this test is to determine the capacity of the equipment to be stored or used under conditions of high humidity combined with cyclic variations of temperature and, in general, with condensation to form on its surface.

To do this, use option 2 of the test preferred UNE 135401-2 EX 1 standard, which is defined in the standard EN 60068-2-30 Db (damp heat cyclic test) 16. This standard also defines use test devices and procedures of preparation, recovery and measures. The test will take place with the equipment  with its maximum settings and load and operating conditions. The minimum severity of the test will be: temperature: 40 ° C number of cycles: 2.

The manufacturer may choose to certify a higher severity, by selecting other values of temperature and number of cycles among those defined by the standard.

More information at: www.dycometal.coml.com 

CCK-40/1000 - CLIMATIC CHAMBER (1000 liters)

DYCOMETAL, company with over 25 years experience in developing simulation chambers for environmental testing, offers customers Climatic Chambers to carry out climatic tests.

HUMID CHAMBER FOR CONDITIONING OF PLASTIC PARTS

Within the plastic industry, polyamide parts must be upgraded to high temperatures and humidity for dimensional stability and impact resistance.

For a homogeneous conditioning, humidity chambers, have a uniform airflow, which guarantees that all parts have the same conditions of temperature and humidity. These cameras tend to be built in stainless steel internally and its internal dimensions tend to be high-volume to put up the largest number of samples simultaneously.

More information at: www.dycometal.com

DYCOMETAL, company with over 25 years experience in developing simulation chambers for environmental testing, offers customers High Humidity Test Chambers to carry out climatic tests.

Accelerated aging in plastic parts: Rain

Currently, plastic parts make up most of the things that surround us: cars, computers, etc. These pieces have been of different quality controls other than the metallic materials. There are many types of plastic, but a difference among them is the time of degradation to which they are subject from its manufacture.

Rain is another factor affecting the degradation of plastic parts. The most prominent trials are those during which parts are wet (dew, rain or moisture after rain periods). Water can contribute to the degradation of plastics.

More details at: www.dycometal.com 

CCL-2900e- RAIN TEST CHAMBER, Special desig for Automotive parts (2900 liters)

DYCOMETAL, company with over 25 years experience in developing simulation chambers for environmental testing, offers customers Rain test Chambers to carry out climatic tests

Accelerated aging in plastic parts: Temperature

Currently, plastic parts make up most of the things that surround us: cars, computers, etc. These pieces have been of different quality controls other than the metallic materials. There are many types of plastic, but a difference among them is the time of degradation to which they are subject from its manufacture.

Temperature is one of the factors affecting the degradation, all chemical reaction is accelerated with increasing temperature, and plastics are no exception, so increasing temperature on plastic parts we increase the degradation of the same. Plastics have a low thermal conductivity, so that if a piece of plastic is exposed to the Sun, its temperature will increase much more, and can reach temperatures well above room temperature..

More information at: www.dycometal.com

AFA-150/5120 - FORCED AIR HEATING OVEN (5120 Liters)

DYCOMETAL, company with over 25 years experience in developing simulation chambers for environmental testing, offers customers Ovens to carry out climatic tests

Aging accelerated in plastic parts: RADIATION

Currently, plastic parts make up most of the things that surround us: cars, computers, etc. These pieces have been of different quality controls, non-metallic materials. There are many types of plastic, but a difference among them is the time of degradation to which they are subject from its manufacture.

One of the factors affecting the degradation is the solar radiation: ultraviolet (UV), visible and infrared (IR); still it UV which most affects the molecular structure of the plastic, accelerating the process of degradation. UV light, accelerated aging chambers allow the simulation of the conditions that the plastic will face during its life, at a certain temperature and under conditions of UV radiation.

More information at: www.dycometal.com 

CCK-40/300 - CLIMATIC CHAMBER WITH SOLAR SIMULATION (300 Liters)

DYCOMETAL, company with over 25 years experience in developing simulation chambers for environmental testing, offers customers Chambers to carry out climatic tests

UNE-EN-60068-2-2, Driy Heat Test – Ovens

The objective of this test is determine the capacity of the electronic equipments to be storage or used under high temperatures.

For this purpose is used the Bd test (dry heat test for samples with low variation of temperature) recommended the standard UNE 135401-2 EX, which is found in the standard EN 60068-2-1.

The test will be done with the equipments in their máximum configuration and load in a workspace with enough dimensions to do tests. The minimum several of temperature will be 60ºC. The manufacturer could opt for certify a lower temperature, between the defined standards

The minimum exposure to a lower temperature will be 16 hours, from the stabilization of the chamber.

More information at: www.dycometal.com 

AFA-150/768 - OVEN (768 Liters)

DYCOMETAL, company with over 25 years experience in developing simulation chambers for environmental testing, offers customers Ovens to carry out climatic tests

UNE-EN-60068-2-1, COLD TEST

The objective of this test is determine the capacity of the electronic equipments to be storage or used under low temperatures.

For this purpose is used the test Ab (cold test for samples that do not dissipate heat with low temperature variation), recommended the standard UNE 135401-2 EX, which is found in the standard EN 60068-2-1. This standards define the equipments to use in the test and the conditioning procedures with the máximum configuration and load, and under conditions of not work, excepting in the last period of low temperature. The minimum severity of the temperature will be -10ºC. The manufacturer could opt for certify a lower temperature, between the defined standards

The minimum exposure to a lower temperature will be 16 hours, from the stabilization of the chamber.

More information in: www.dycometal.com 

CET-40/1000 - TEMPERATURE TEST CHAMBER (1000 Liters)

DYCOMETAL, company with over 25 years experience in developing simulation chambers for environmental testing, offers customers Temperature Test chambers to carry out climatic tests

DYCOMETAL BIO-SCIENCE CHAMBERS

In the R&D market, the climatic chamber has an important application inside of the botanic sector, thanks to the Plants Growth Chambers and seeds germination chamber.

These chambers present the optimal conditions in humidity, temperature and solar radiation, to generate the optimal atmosphere for the growing of the plants. It’s possible to control other variables like gases (CO2, CO, etc).

The dimensions of the chamber can change from the smaller laboratory until the walk-in chambers, where is possible to do extensive cultives.

More information in: www.dycometal.com 

DYCOMETAL, company with over 25 years experience in developing simulation chambers for environmental testing, offers customers PLANTS GROWTH CHAMBERS AND SEEDS GERMINATION CHAMBERS  to carry out such tests.

NEW YOUTUBE CHANNEL

Dear customers and Friends,

From DYCOMETAL, we want to approach our products to all , for this reason we have opened a new youtube channel where we will put the different products from DYCOMETAL.

You can see the new videos from our products in this link:

https://www.youtube.com/channel/UCQI2YVfttjcCy2igQ9b2A-A

We will upload all the special products and standard products. We hope that you will enjoy it

Remember that you have more information in our website: www.dycometal.com 

LOOKING FOR PARTNERS

We are currently looking for an experienced partners to distribute our equipments globally.

It's necessary experience in the environmental test chamber industry preferred, with an own technical service preferred. 

If you are interested please contact to: delegacioncentro@dycometal.com

MIL-STD-810, SALT SPRAY TEST

The objective of the salt spray test is to determine the effectiveness of protective coatings and surface finishes, and is used to determine the effects of salt deposicones in electrical and physical materials.

The  samples will be placed in the chamber, and they will be exposed to an indirect salt spray with neutral pH (beween 6.5 to 7.2). the concentration must to be 5±1%, and the falla-out rate must to be between 0.5 and 3 ml/80cm2/hour. The temperature of the test will be +35ºC. After 48 hours of test, the samples will be dried another 48 hours.

SSC-400, SALT SPRAY CHAMBER (400 liters)

DYCOMETAL, company with over 25 years experience in developing simulation chambers for environmental testing, offers customers SALT SPRAY CHAMBERS  to carry out climatic tests.

MIL-STD-810 Method 506.4, RAIN TESTRAIN TEST CHAMBER

The Rain tightness tests are performed to different components to evaluate the IP degree of protection, in the Rain test Chambers.

MIL-STD-810 test method in its method 506.4, to evaluate any element to be exposed to rain, spraying or dripping water during storage or transport operation.

Its goal is to determine:

-      The effectiveness of covers, housings and seals to prevent water penetration into the material

-       The ability of the material to satisfy the requirements before and after exposure to water

-       Determine whether there is any physical deterioration of the material caused by rain

-       The effectiveness of any system of water extraction 

-       The effectiveness of protection offered by the material.

CLL-512, Rain Test Chamber (512 liters)

DYCOMETAL, company with over 25 years experience in developing simulation chambers for environmental testing, offers customers RAIN TEST CHAMBERS CHAMBERS  to carry out climatic tests.

MIL-STD-810 Method 510.4, Dust and Sand Test

The dust tightness tests are performed to different components to evaluate the IP degree of protection, in the  Dust Chambers.

MIL-STD-810 test method in its method 510.4, set the test parameters to assess any mechanical, optical, electrical, electronic, electromechanical and electrochemical element which may be exposed during use or storage in dusty atmospheres or sand.

This standard establishes two parts:

 •  Small particles of dust (˂149 microns) to assess the system's resistance to dust against obstructions, cracks, etc. 

 •    Blowing sand (150-850 microns) to evaluate the systems and determine whether the material can be stored and operated under conditions of blowing sand without degrading performance.

CP-216, DUST TEST CHAMBER (216 liters)

DYCOMETAL, company with over 25 years experience in developing simulation chambers for environmental testing, offers customers DUST TEST CHAMBERS CHAMBERS  to carry out climatic tests.