IEC 60529 TESTING, RAIN TEST, IPX3 AND IPX4 DEGREES. CLL-1000 RAIN TEST CHAMBER

Sometimes our clients don't need a custom solution; a standard solution is sufficient for their environmental testing needs. That's where our standard solutions come in. This was the case for the electronics department of a European university that was looking for a rain test chamber.
 
The requirements were:
👉 Volume of approximately 1000 liters.
👉 Compliance with IEC 60529.
👉 IPX3 and IPX4 protection ratings.
👉 Flow control.
 
OUR SOLUTION: Our standard rain test chamber, model CLL-1000, with a 1000-liter capacity and an 800 mm diameter arch. It features a height-adjustable sample holder and a power supply for the sample. A standard solution for a standard need.
 
Would you like to more know?
📩 Contacto: comercial@dycometal.com
🌐 Web: www.dycometal.com

#dycometal #environmentaltesting #EnvironmentalSimulation #RainTesting #electronic #chamber #IEC60529 #IPX #IPXY #testing #chamber #climatic #RAndD #Innovation #QualityAssurance

SPECIAL RAIN TEST CHAMBER FOR DEGREES: IPX3,4,4K, 6K & 9K ACCORDING WITH ISO 20653, CLL-2700e

In the automotive sector, there are many elements that have to withstand heavy rain or high pressure water spray when cleaning vehicles, such as luminaires. In this case, the correct functioning and tightness of the luminaires must be guaranteed after extreme water spray conditions. The ISO 20653 standard establishes a series of rain tests for electrical enclosures, classified according to the type of test into degrees of protection. In addition to the IEC 60529 tests, this standard adds specific codes with the letter K, which describe special requirements for road vehicles.

The CLL-2700e chamber has been developed to comply with the ISO20653 standard, for tests with IPX,3 IPX4 (rain arc), IPX4 (high pressure rain arc), IPX6K (high speed and high pressure water jet) as well as IPX9K (high pressure and high temperature water). With a volume of 2700 litres (1400 x 1400 x 1400 mm), it allows testing on luminaires of various sizes.

For more information, please contact us by email: comercial@dycometal.com or on our website: www.dycometal.com . 

DYCOMETAL, a company with more than 40 years of experience in the development of simulation chambers for environmental testing, offers its customers ENVIRONMENTAL TESTING SOLUTIONS ADAPTED TO THEIR NEEDS.

RAIN TEST CHAMBERS, IN COMPLIANCE WITH PROTECTION STANDARDS

The standards for protection against external agents (dust or rain), allow the degree of protection of electronic enclosures against the introduction of external elements to be determined. Within the automotive standards, each manufacturer has its own test standards, such as VOLKSWAGEN’s TL-956 section 6.2.

The CLL-1000 chamber has been configured to meet rain tests for IPX3, IPX4 and has also been modified to meet IPX4 tests (Splash water with increased pressure).

For more information, please contact us by email: comercial@dycometal.com or on our website: www.dycometal.com . 

DYCOMETAL, a company with more than 40 years of experience in the development of simulation chambers for environmental testing, offers its customers ENVIRONMENTAL TESTING SOLUTIONS ADAPTED TO THEIR NEEDS.

PRODUCT BULLETIN: CLL-4500e, Rain Test Chamber for Durability Test of Wiper

Wipers aim to provide the driver visibility conditions minimum through the sweep of the outer surface of the windscreen. To do this they must pass a test of endurance and durability under various controlled conditions. During this test, the sweep rate of the wiper should be editable throughout the trial, sprayed water flow will be controlled and such water must have certain conditions of quality. The water flow must be symmetrically distributed on the windshield as well as having a certain temperature. The entire process should be evaluated for a number of cycles in accordance with the rules established.

The CLL-4500e chamber has been designed to introduce the complete windscreen inside of the chamber, so that the test would be the most faithful to the reality. The chamber presents a double wing door with total access to the workspace so that the introduction of the samples is convenient. The vision system of the rain test chamber allows an analysis of the behaviour of the wipers and the water.

If you want more information, please contact us in comercial@dycometal.com or in our website: www.dycometal.com

DYCOMETAL, company with over 25 years of experience in the development of Chambers for environmental testing simulation, offers its customers RAIN TEST CHAMBERS to do these tests.

Accelerated aging in plastic parts: Rain

Currently, plastic parts make up most of the things that surround us: cars, computers, etc. These pieces have been of different quality controls other than the metallic materials. There are many types of plastic, but a difference among them is the time of degradation to which they are subject from its manufacture.

Rain is another factor affecting the degradation of plastic parts. The most prominent trials are those during which parts are wet (dew, rain or moisture after rain periods). Water can contribute to the degradation of plastics.

More details at: www.dycometal.com 

CCL-2900e- RAIN TEST CHAMBER, Special desig for Automotive parts (2900 liters)

DYCOMETAL, company with over 25 years experience in developing simulation chambers for environmental testing, offers customers Rain test Chambers to carry out climatic tests

BUILDING. Freeze- thaw chamber

Building materials installed outdoors, must endure for years strong climate action: rain, ice, sun, wind, etc. In winter, they continue to experience large temperature changes in the day / night cycle, moisture absorption during the day and freezing at night, causing significant degradation of the material.

With freeze-thaw chambers, manufacturers of building materials can optimize their products in the laboratory, and as a result can be minimized or eliminated the damage.

Standards like: UNE-EN ISO 10545, UNE 67048, UNE 22174, etc. Are used in these elements.

CHD. Freeze-Thaw chamber with thermostatic bath

DYCOMETAL, company with over 25 years experience in developing simulation chambers for environmental testing, offers customers FREEZE-THAW CHAMBERS  to carry out such tests.

BUILDING. Freeze-thaw chamber over TILES.

All products that We met at the day, must be tested against weather conditions, including elements that happen to us unnoticed as our roof shingles. These building elements have to be tested to simulated weather conditions which will face over its lifetime.

DYCOMETAL, has supplied climatic chambers for testing resistance to freeze-thaw  on tiles, as shown in the video shown below, recorded by the "MADE IN SPAIN" RTVE program.

http://www.rtve.es/alacarta/videos/fabricando-made-in-spain/fabricando-made-in-spain-fabricamos-tejas-ceramicas/2858918/?fb_action_ids=10204717404968407&fb_action_types=og.recommends&fb_source=other_multiline&action_object_map=%7B%2210204717404968407%22%3A985282608154780%7D&action_type_map=%7B%2210204717404968407%22%3A%22og.recommends%22%7D&action_ref_map=%5B%5D

CHD Series- Freeze-Thaw chamber

DYCOMETAL, company with over 25 years experience in developing simulation chambers for environmental testing, offers customers FREEZE-THAW CHAMBERS  to carry out such tests

DRIVE-IN chambers

Climatic test reproduce the climatic conditions in temperature and humidity, to which the equipment or materials will be subjected during operation, transport or storage.

When we have to test samples with big dimensions and big weight, like complete vehicle; it’s not posible to test these samples in a estándar chamber. It is necessary to use modular climatic chambers like DRIVE-IN chambers.

DRIVE-IN chambers are a modification of the Walk-in chambers, where the customer can test cars, bus, trucks or also trains.

These chambers can simulate any kind of environmental conditions: temperatura, humidity, solar radiation, salt spray, dust, rain,…

DYCOMETAL, company with over 25 years experience in developing simulation chambers for environmental testing, offers customers DRIVE-IN CHAMBERS to carry out such tests.

Rain test Chamber, CLL series

Rain test is done over different components to evaluate the IP degree protection,according standard DIN 40 053, in the rain test chambers

Feature Nº.	Protection Type	Equipment
IP-X1	Vertical fall of drops of water	Drip box, gyratory platform
IP-X2	Waterfalls with a 15 degrees maximum tilt	Drip box, static platform
IP-X3	Water falls as rain	Oscillatory pipe or sprinkler head
IP-X4	Water projections	Spray with fix/swivel, gyratory platform.
IP-X5	Water jets	Spray with nozzle Ø 6.3 mm
IP-X6	Strong jets of water	Spray with nozzle 12.5 mm Ø
IP-X7	emporary immersion in water	Bath immersion

To big lights, DYCOMETAL, has developed a special equipment to do the rain test

The equipment is manufactured by a drip box (IPX1 and IPX2), two rain arcs and showers (IPX3 and IPX4). We have provided also the use of the circuits for 5 and 6 degree test.

The control of the systems comes commanded by a powerful microprocessor, which regulate wáter spray time, the measure of the wáter flow in l/min, and electrical feed to the sample by the connection box in the rotating plate.

DYCOMETAL, company with over 25 years experience in developing simulation chambers for environmental testing, offers customers Rain test Chambers to carry out such tests.